avionics 92
- Pitot Static Check
- Engine Hose & Wire Clean Up
- Coolant Leak Checks and Misc Tasks
- Misc Fuselage Work - Data Plate, MFD
- High Fuel Pressure Conclusion, Brake Conditioning, and Magnetometer Calibration
- Fuel Pressure Test, Seat Adjustment, Tail Fairing
- Fuel Tank Calibration, Fuel Flow Test, and ADHARS Calibration
- Calibration on Avionics and Nose Wheel, and adding coolant
- Calibrating Control Surfaces and Cable Routing
- Post Wing Mounting Work - Part 4 - The Boost Pump Saga
- Wing Mounting Prep - Center Channel Cover
- Redoing Propeller Safety Wire, Wiring Clean Up, Air Filter Fitting, Oil Purge
- Coolant System Fluid Lines - Part 1
- Firewall loom sealing bracket
- Mounting Wing Harness Connector, Wire Management on Firewall Forward
- Engine Harness - Part 6 - Fixing harness wires & testing
- Engine Harness - Part 5 - Debugging CAN wires
- Engine Harness - Part 4 - Continue with Wiring Investigation
- Engine Harness - Part 3 - Wiring Issue
- Making Sensor Connectors & PCV Mount
- Engine Harness - Part 2 - Starter Cables and Fuel Pressure Sender
- Engine Harness - Part 1 - Fusebox and Starter
- ECU & HIC
- Installing new Master Relay
- Firewall Wiring Cleanup, and Master Relay
- Firewall Wiring and Heater Hose Cleanup
- Regulator B Ground Wire & Misc Clean Up
- Starter Relay and Fusebox, Regulator
- Misc Work on Firewall Forward
- Completed ELT Wiring
- Checked GPS Antenna Installation
- Installing left rear window
- Rebuilt battery cables, installed shunt cover
- Airmaster controller, FP1 connector
- Re-installing GTP 59 (OAT Probe)
- Installing Instrument Panel & Prepping Fuel Selector
- Installing GTP 59 (OAT Probe)
- Fixed GMU11 connection
- First power on!
- Firewall Forward Wiring
- Test fitting throttle quadrant
- Center console work
- Routing misc wires and fluid lines
- Wiring on the firewall forward
- Finishing up trim motor and rudder cable
- Final assembly: vertical stabilizer and rudder
- Lots of things before putting on dashboard
- Routing some more wires before instrument panel
- Test fitting instrument panel and more prep: cabin heater work, upholstery etc
- Preparing instrument panel fitting
- Mounting control stick wiring connector to airframe
- Boost pump controller, cabin heat duct, and upholstery
- Routing avionics harness
- Comm2 Antenna
- Audio jack issues
- Audio jack ground loop(??)
- Wiring harness (part 5): Antennas and more wires
- Wiring harness (part 4) & coax
- Continue on wiring harness (part 3)
- Continue on wiring harness
- Working on avionics rack
- Routing harness part2: wing connectors and GTR 205xR
- Starting to route harness, and relocating ELT
- Some riveting, and starting on carpet (luggage extension)
- Installing Antenna Mounting Plates
- Pilot side control stick
- Avionics rack support
- Autopilot Servos
- Installed ELT
- NACA Duct & Static port
- Canopy part 1: paint and wiring
- Rear fuselage: Misc work before closing the top skin
- Rear fuselage: luggage area, static port, GMU 11
- Rear fuselage skin & fixing a damaged inner skin
- Left wing: nav light is on
- Left wing skin misc clean up, and discussing panel with MPB
- Right wing: lights and lens, wing tip and wing stand
- Prosealing the right fuel tank, left wing leading edge & lights
- Left top skin, and landing lights
- Misc work, but mostly fuel tank
- Fuselage kit arrived, and left aileron
- Installing pitot tube
- Lots of things going on the right wing, and starting on the left
- right wing harness
- Right bottom skin riveted
- Misc non-build updates
- Elevator rivet filling
- Trim motor wiring
- Vertical stabilizer wiring
- Wiring delphi connector for tail light
- Wire standoff and EAA Tech Counseling visit
- Installing Taillight